Comware

Hi Everyone,

So I've got some 2930F POE+ switches (specifically some JL255A's) and I've plugged in a door control device which requires 1.5A and 20W, which according to the data sheet for this switch is well below it's capabilities. (2.5A 445W) so should comfortably power the device - the problem is that it doesn't and i get an "PD Over Current indication" error on the switch.

Initially we thought this indicated the device was faulty, however when plugged into a tiny, cheap alternative POE+ switch it powers up fine, but it doesn't work in any of the 2930F POE+ switches we have

Any ideas what could be the issue? I've given the port in question high priority for power and there's plenty of Wattage available to the switch (300W unused capacity) but I must be missing something. Any help would be greatly appreciated!

#Aruba
#Port

Hello ,

PD over current indicates that an attached load has attempted to draw too much current from the switch.
Is it possible to share 'show log' output?
Also share 'show power-over-ethernet' output
And
show power-over-ethernet <effected port number > Status/ Counters


Also can you try to disable and re-enable the Poe port?

Running software version?



Thanks!

Hi akg7,

Sure thing. Show logging doesn't show much other than what I mentioned previously 

W 07/29/21 10:06:23 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:26 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:29 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:33 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:35 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:38 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:41 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:44 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:47 00562 ports: port 11 PD Over Current indication.
W 07/29/21 10:06:50 00562 ports: port 11 PD Over Current indication.
It's just this repeated constantly.

For show power-over-ethernet we have

Status and Counters - System Power Status

Chassis power-over-ethernet:

Total Available Power : 370 W
Total Power Drawn : 59 W +/- 6W
Total Power Reserved : 63 W
Total Remaining Power : 307 W

Internal Power

Main Power
PS (Watts) Status
----- ------------- ---------------------
1 370 POE+ Connected

Will need to get back to you on the "show power-over-ethernet <effected port number > Status/ Counters" output, it's not currently plugged into the 2930F as we needed the door to work and the device operates the door, so it's in a separate POE+ box at the moment. I'll see if I can get it switched back to get that info

I can confirm however that we did try disabling/renabling the port, trying it in other 2930F's and trying it in alternate ports

Sorry for the delay, here is that final bit of output you requested

 

Status and Configuration Information for port 11

Power Enable : Yes PoE Port Status : Fault
PLC Class/Type : 0/- Priority Config : high
DLC Class/Type : 0/- Pre-std Detect : off
Alloc By Config : usage Configured Type :
Alloc By Actual : usage PoE Value Config : n/a

PoE Counter Information

Over Current Cnt : 787,475 MPS Absent Cnt : 9
Power Denied Cnt : 0 Short Cnt : 0

LLDP Information

PSE Allocated Power Value : 0.0 W PSE TLV Configured : dot3, MED
PD Requested Power Value : 0.0 W PSE TLV Sent Type : dot3
MED LLDP Detect : Disabled PD TLV Sent Type : n/a

Power Information

PSE Voltage : 0.0 V PSE Reserved Power : 0.0 W
PD Amperage Draw : 0 mA PD Power Draw : 0.0 W

 

thank you

Hi @Adam-COWC 

The POE port ststus is showing as Fault this means the switch detects a problem with the connected PD.  As this is a PoE+ switch the PD can be drawn up to 25.5 watts. 

Status and Configuration Information for port 11

Power Enable : Yes PoE Port Status : Fault

You need to log case with support team for this issue.

Hello @ Adam-COWC,

Power Enable : Yes PoE Port Status : Fault

It seems there is a hardware issue.

Can you share 'show version' output to get the software version and is there any possibility to reboot the switch?

Thanks!

Hi there,

sure thing, here is the output

show version

Image stamp: /ws/swbuildm/rel_ajanta_qaoff/code/build/lvm(swbuildm_rel_ajanta_qaoff_rel_ajanta)
Jun 26 2020 00:40:02
WC.16.10.0009
78
Boot Image: Primary

Boot ROM Version: WC.16.01.0008
Active Boot ROM: Primary

I can also confirm that after a reboot the error persists with no change

Hello @Adam-COWC ,

I checked latest software version and bug is ruled out here.

Want to know if the fault is present in other interfaces as well?

And, is there any possibility to reboot the switch?

Thanks!

 

 

Hi @akg7 

The fault is present on multiple 2930F's and we've tried multiple different interfaces on each. I can also confirm that we have rebooted the switch, but the error is the same

In any other situation i'd blame the device on the other end being faulty, but as the device works when put in a small POE+ miniswitch that somewhat rules that out 

Hello @Adam-COWC 

W 07/29/21 10:06:23 00562 ports: port 11 PD Over Current indication.

Error 00562 indicated The powered device (PD) connected to the port has requested more than 15.4 watts of power. This may indicate a short-circuit or other problem in the PD.

Pelase share below command output:

show power-over-ethernet <port 11 or other ports>

Can you try to run below command:

HP Switch(config) # interface <interface number> poe-allocate-by value
HP Switch(config) # int <interface number> poe-value 30

 

Thanks!

Hi @akg7 

I am happy to confirm that manually allocating the value to 30 has allowed the door to power up, which is great, though now comes the follow up question - if the switch is capable of doing this, why didn't it automatically provide this power? I'm fairly certain that the default power provision is set to Auto?

For reference, this is now the draw for that port

Status and Configuration Information for port 11

Power Enable : Yes PoE Port Status : Delivering
PLC Class/Type : 4/2 Priority Config : high
DLC Class/Type : 0/- Pre-std Detect : off
Alloc By Config : value Configured Type :
Alloc By Actual : value PoE Value Config : 30

PoE Counter Information

Over Current Cnt : 216 MPS Absent Cnt : 0
Power Denied Cnt : 0 Short Cnt : 0

LLDP Information

PSE Allocated Power Value : 25.5 W PSE TLV Configured : dot3, MED
PD Requested Power Value : 0.0 W PSE TLV Sent Type : dot3
MED LLDP Detect : Disabled PD TLV Sent Type : n/a

Power Information

PSE Voltage : 54.5 V PSE Reserved Power : 30.0 W
PD Amperage Draw : 385 mA PD Power Draw : 21.0 W

 

Thanks Again

 

 

Hello @Adam-COWC ,

 

I believe power provision was set defaul 'usage' and this provides @ average15.4 W each port out of total 370 watss available.

If power provision is more than 15.4 W then either use 'class' or ' value'.

int <port-list> poe-allocate-by [ usage | class | value ]

Allows you to manually allocate the amount of PoE power for a port by either its class or a defined value.

usage: The automatic allocation by a PD.

class: Uses the power ramp-up signature of the PD to identify which power class the device will be in. 

value: A user-defined level of PoE power allocated for that port.

 

Hello @Adam-COWC ,

Has my post helped you to answer your query?

 

Thanks!

@akg7 

Yes very much thank you, I have accepted your answer as the solution as well

Try this

which interface you want to provide.

Interface port# power-over-ethernet 

write memory 

restart the switch and check the status.

From my opinion its not a switch issue, only need the exact command.

I get same error (PD over current) on 2930 when connecting network attached bells, which makes no sense as the power usage is negligible

  Member 2 Power
  Available: 370 W  Used: 45 W  Remaining: 325 W

 PoE    Pwr  Pwr      Pre-std Alloc Alloc  PSE Pwr PD Pwr  PoE Port     PLC PLC
 Port   Enab Priority Detect  Cfg   Actual Rsrvd   Draw    Status       Cls Type
 ------ ---- -------- ------- ----- ------ ------- ------- ------------ --- ----
 2/1    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/2    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/3    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/4    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/5    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/6    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/7    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/8    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/9    Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/10   Yes  low      off     usage usage  2.3 W   2.3 W   Delivering   3    1
 2/11   Yes  low      off     usage usage  2.3 W   2.2 W   Delivering   3    1
 2/12   Yes  low      off     usage usage  1.6 W   1.5 W   Delivering   3    1
 2/13   Yes  low      off     usage usage  2.2 W   2.2 W   Delivering   3    1
 2/14   Yes  low      off     usage usage  2.2 W   2.2 W   Delivering   3    1
 2/15   Yes  low      off     usage usage  2.1 W   2.1 W   Delivering   3    1
 2/16   Yes  low      off     usage usage  2.2 W   2.2 W   Delivering   3    1
 2/17   Yes  low      off     usage usage  2.3 W   2.2 W   Delivering   3    1
 2/18   Yes  low      off     usage usage  2.2 W   2.1 W   Delivering   3    1
 2/19   Yes  low      off     usage usage  2.2 W   2.1 W   Delivering   3    1
 2/20   Yes  low      off     usage usage  1.7 W   1.7 W   Delivering   3    1
 2/21   Yes  low      off     usage usage  2.2 W   2.2 W   Delivering   3    1
 2/22   Yes  low      off     usage usage  2.5 W   2.4 W   Delivering   3    1
 2/23   Yes  low      off     usage usage  2.3 W   2.2 W   Delivering   3    1
 2/24   Yes  low      off     usage usage  2.3 W   2.2 W   Delivering   3    1
 2/25   Yes  low      off     usage usage  2.2 W   2.2 W   Delivering   3    1
 2/26   Yes  low      off     usage usage  2.2 W   2.2 W   Delivering   3    1
 2/27   Yes  low      off     usage usage  2.2 W   2.2 W   Delivering   3    1
 2/28   Yes  low      off     usage usage  2.2 W   2.2 W   Delivering   3    1
 2/29   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/30   Yes  low      off     usage usage  2.3 W   2.2 W   Delivering   3    1
 2/31   Yes  low      off     usage usage  2.2 W   2.1 W   Delivering   3    1
 2/32   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/33   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/34   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/35   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/36   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/37   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/38   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/39   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/40   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/41   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/42   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/43   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/44   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/45   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/46   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/47   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    -
 2/48   Yes  low      off     usage usage  0.0 W   0.0 W   Searching    0    

------------------------------
spgsitsupport
------------------------------

Original Message:
Sent: Aug 03, 2021 06:24 AM
From: Archive User
Subject: 2930F POE+ Switch not providing POE+ power

Hi Everyone,

So I've got some 2930F POE+ switches (specifically some JL255A's) and I've plugged in a door control device which requires 1.5A and 20W, which according to the data sheet for this switch is well below it's capabilities. (2.5A 445W) so should comfortably power the device - the problem is that it doesn't and i get an "PD Over Current indication" error on the switch.

Initially we thought this indicated the device was faulty, however when plugged into a tiny, cheap alternative POE+ switch it powers up fine, but it doesn't work in any of the 2930F POE+ switches we have

Any ideas what could be the issue? I've given the port in question high priority for power and there's plenty of Wattage available to the switch (300W unused capacity) but I must be missing something. Any help would be greatly appreciated!

#Aruba
#Port