We replaced an AP125 with an AP115 but it cannot be reached by our OOB controller, only via serial on a laptop. On the AP125, I statically assigned the parameters it uses, ie: ipaddr, gatewayip, master, serverip, netmask. However, I am unable to get into the "Press enter to stop autoboot" prompt to do this. When I press enter, nothing happens.
The AP is connected to the first port on the 3200XM controller with the ENET interface on the AP115.
The print out of the AP is:
Aruba Networks
ArubaOS Version 6.3.1.0 (build 38874 / label #38874)
Built by p4build@cyprus on 2013-07-03 at 19:14:29 PDT (gcc version 4.3.3)
CPU Rev: 1130
955x CPU
flash_size passed from bootloader = 32
arg 1: mem=256M
Flash variant: default
cpu apb ddr apb ath_955x_sys_frequency: cpu 720 ddr 600 ahb 200
Cache parity protection disabled
ath_timer_init: plat time init done
Using 360.000 MHz high precision timer. cycles_per_jiffy=720000
Memory: 251520k/262144k available (1927k kernel code, 10420k reserved, 844k data, 3796k init, 0k highmem)
available.
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=17933312
LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com> ..................................................................................................................................................................................................................................................................................
qca955x_pcibios_init: bus 0
qca955x_pcibios_init(1239): PCI 0 CMD write: 0x356
qca955x_pcibios_init: bus 1
qca955x_pcibios_map_irq: IRQ 75 for bus 0
ATH GPIOC major 0
wdt: registered with refresh
Enabling Watchdog
Talisker RSSI LED initialization
Concatenating MTD devices:
(0): "bank1"
(1): "bank2"
into device "flash"
Creating 1 MTD partitions on "flash":
0x00000000-0x02000000 : "flash"
i2c /dev entries driver
i2c-talisker: using default base 0x18040000
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
Starting Kernel DES KAT ...Completed Kernel DES KAT
Starting Kernel AES KAT ...Completed Kernel AES KAT
Starting Kernel AESGCM KAT ...Completed Kernel AESGCM KAT
Domain Name: arubanetworks.com
No panic info available
qca955x_GMAC: Length per segment 1536
955x_GMAC: qca955x_gmac_attach
955x_GMAC: qca955x_set_gmac_caps
Currently in polling mode unit0
mac:0 Registering S17....
qca955x_GMAC: RX TASKLET - Pkts per Intr:100
qca955x_GMAC: Mac address for unit 0:8079bbc0
qca955x_GMAC: 18:64:72:c2:30:f6
qca955x_GMAC: Max segments per packet : 1
qca955x_GMAC: Max tx descriptor count : 128
qca955x_GMAC: Max rx descriptor count : 128
qca955x_GMAC: Mac capability flags : 2201
_athrs17_mac0_intf done
athrs17_reg_init:done
Phy setup Complete
drvlog_mod: module license 'Proprietary' taints kernel.
AP xml model 72, num_radios 2 (jiffies 3516)
init_asap_mod: installation:0
radio 0: band 1 ant 0 max_ssid 16
radio 1: band 0 ant 0 max_ssid 16
Starting watchdog process...
Getting an IP address...
To set s17 LOOKUP_CTRL_REG registers, flag 0
athr_gmac_ring_alloc Allocated 2048 at 0x806d3000
athr_gmac_ring_alloc Allocated 2048 at 0x8ef7e800
955x_GMAC: eth0 in RGMII MODE
Scorpion -----> S17 PHY
FINAL XMII VAL after RX Calibration - 0x84000101
Error: cannot be initialized twice!
athrs17_reg_init:done
Setting PHY...
Phy setup Complete
To set s17 LOOKUP_CTRL_REG registers, flag 1
ADDRCONF(NETDEV_UP): bond0: link is not ready
Enet:0 port0 up
eth0 RGMII 1000Mbps full duplex
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
(The prompt just stops here and doesn't restart or anything)
Could this be because the AP115 does not support ArubaOS 6.3? I tried looking on the release notes and on http://www.arubanetworks.com/support-services/end-of-life-products/ but I couldn't find the answer.