Wired Intelligent Edge

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?




​

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281
------------------------------

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos
------------------------------

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles
------------------------------

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

I already read the best practice, I tried with configuration, when i show the interface is ok but the lag interface 3 is blocked



Original Message:
Sent: Feb 09, 2021 03:17 AM
From: Vincent Giles
Subject: ARUBA 8325 VSX and OSPF

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

When i see my conf :
 on core :
!
vlan 3
vsx-sync
description INTER-SITE TRANSITE VLAN

!
interface lag 3 multi-chassis
no shutdown
description INTER-SITE VSX LAG
no routing
vlan trunk native 1
vlan trunk allowed 3,100,103-107
lacp mode active
spanning-tree bpdu-filter

!
interface 1/1/51
no shutdown
mtu 9198
description INTER-SITE Link
lag 3
interface 1/1/54
no shutdown
mtu 9198
description INTER-SITE Link
lag 3

!
interface vlan 3
ip mtu 9198
vsx active-forwarding
ip address 10.0.3.1/29
ip ospf 1 area 0.0.0.0
ip ospf cost 1000



and same configuration on the 3 other Switch, just the IP of the interface vlan 3 change :
- on core 2 :ip address 10.0.3.2/29
​- on srv 1:ip address 10.0.3.3/29
- on srv 2 :ip address 10.0.3.4/29
Original Message:
Sent: Feb 09, 2021 08:58 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I already read the best practice, I tried with configuration, when i show the interface is ok but the lag interface 3 is blocked

And when i want to show the lacp interface, i have this LACP-BLOC

Original Message:
Sent: Feb 09, 2021 03:17 AM
From: Vincent Giles
Subject: ARUBA 8325 VSX and OSPF

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

You need to fix the LACP-BLOCK,

Do you have check the lldp neighbor ?

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281
------------------------------

Original Message:
Sent: Feb 09, 2021 08:58 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I already read the best practice, I tried with configuration, when i show the interface is ok but the lag interface 3 is blocked

And when i want to show the lacp interface, i have this LACP-BLOC

Original Message:
Sent: Feb 09, 2021 03:17 AM
From: Vincent Giles
Subject: ARUBA 8325 VSX and OSPF

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

Yes I made lldp neighbor and i see all my architecture

Original Message:
Sent: Feb 09, 2021 03:37 PM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

You need to fix the LACP-BLOCK,

Do you have check the lldp neighbor ?

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 09, 2021 08:58 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I already read the best practice, I tried with configuration, when i show the interface is ok but the lag interface 3 is blocked

And when i want to show the lacp interface, i have this LACP-BLOC

Original Message:
Sent: Feb 09, 2021 03:17 AM
From: Vincent Giles
Subject: ARUBA 8325 VSX and OSPF

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

Unless you need a VLAN trunk to that switch for transport more VLANS I Would use to /30 or /31, one for each connection to the VSX and use OSPF and ECMP.

------------------------------
Best Regards

Tom Roholm
------------------------------

Original Message:
Sent: Feb 10, 2021 08:52 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Yes I made lldp neighbor and i see all my architecture

Original Message:
Sent: Feb 09, 2021 03:37 PM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

You need to fix the LACP-BLOCK,

Do you have check the lldp neighbor ?

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 09, 2021 08:58 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I already read the best practice, I tried with configuration, when i show the interface is ok but the lag interface 3 is blocked

And when i want to show the lacp interface, i have this LACP-BLOC

Original Message:
Sent: Feb 09, 2021 03:17 AM
From: Vincent Giles
Subject: ARUBA 8325 VSX and OSPF

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

I try with  /30 for my first version and i have the same problem's, now i use /29 for make like the best practice
Original Message:
Sent: Feb 10, 2021 08:57 AM
From: Tom Roholm
Subject: ARUBA 8325 VSX and OSPF

Unless you need a VLAN trunk to that switch for transport more VLANS I Would use to /30 or /31, one for each connection to the VSX and use OSPF and ECMP.

------------------------------
Best Regards

Tom Roholm

Original Message:
Sent: Feb 10, 2021 08:52 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Yes I made lldp neighbor and i see all my architecture

Original Message:
Sent: Feb 09, 2021 03:37 PM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

You need to fix the LACP-BLOCK,

Do you have check the lldp neighbor ?

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 09, 2021 08:58 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I already read the best practice, I tried with configuration, when i show the interface is ok but the lag interface 3 is blocked

And when i want to show the lacp interface, i have this LACP-BLOC

Original Message:
Sent: Feb 09, 2021 03:17 AM
From: Vincent Giles
Subject: ARUBA 8325 VSX and OSPF

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

Ok i'm comeback for the new, i try a new conf and it's work!!!

My problem is  the P2P between the vlan transit for my VSX.

I made no ip ospf network point-to-point on every interface of my architecture and it's work!!
Original Message:
Sent: Feb 10, 2021 09:31 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I try with  /30 for my first version and i have the same problem's, now i use /29 for make like the best practice
Original Message:
Sent: Feb 10, 2021 08:57 AM
From: Tom Roholm
Subject: ARUBA 8325 VSX and OSPF

Unless you need a VLAN trunk to that switch for transport more VLANS I Would use to /30 or /31, one for each connection to the VSX and use OSPF and ECMP.

------------------------------
Best Regards

Tom Roholm

Original Message:
Sent: Feb 10, 2021 08:52 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Yes I made lldp neighbor and i see all my architecture

Original Message:
Sent: Feb 09, 2021 03:37 PM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

You need to fix the LACP-BLOCK,

Do you have check the lldp neighbor ?

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 09, 2021 08:58 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I already read the best practice, I tried with configuration, when i show the interface is ok but the lag interface 3 is blocked

And when i want to show the lacp interface, i have this LACP-BLOC

Original Message:
Sent: Feb 09, 2021 03:17 AM
From: Vincent Giles
Subject: ARUBA 8325 VSX and OSPF

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​

Hi Artnod,

We require a similar configuration.
Could you please share the configuration that worked for you?

Thanks

Original Message:
Sent: Feb 11, 2021 09:59 AM
From: Artnod
Subject: ARUBA 8325 VSX and OSPF

Ok i'm comeback for the new, i try a new conf and it's work!!!

My problem is  the P2P between the vlan transit for my VSX.

I made no ip ospf network point-to-point on every interface of my architecture and it's work!!
Original Message:
Sent: Feb 10, 2021 09:31 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I try with  /30 for my first version and i have the same problem's, now i use /29 for make like the best practice
Original Message:
Sent: Feb 10, 2021 08:57 AM
From: Tom Roholm
Subject: ARUBA 8325 VSX and OSPF

Unless you need a VLAN trunk to that switch for transport more VLANS I Would use to /30 or /31, one for each connection to the VSX and use OSPF and ECMP.

------------------------------
Best Regards

Tom Roholm

Original Message:
Sent: Feb 10, 2021 08:52 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Yes I made lldp neighbor and i see all my architecture

Original Message:
Sent: Feb 09, 2021 03:37 PM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

You need to fix the LACP-BLOCK,

Do you have check the lldp neighbor ?

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 09, 2021 08:58 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

I already read the best practice, I tried with configuration, when i show the interface is ok but the lag interface 3 is blocked

And when i want to show the lacp interface, i have this LACP-BLOC

Original Message:
Sent: Feb 09, 2021 03:17 AM
From: Vincent Giles
Subject: ARUBA 8325 VSX and OSPF

Did you take a look on the VSX Best Practices that contains several examples.
This may help you to determine as well if you need routed ports instead of VSX LAG+transit VLAN.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00094242en_us

------------------------------
Vincent Giles

Original Message:
Sent: Feb 08, 2021 09:27 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

if i understand, i need to create a transit vlan for point-to-point like the vlan 2 and 3 on my schema, and i need to put th'is vlan on the lag.
Can you tell me if my configuration is good or not? on the switch serveur, i have a vlan 200 for the differents server and on the Core I have three vlan user only.

On the Serveur 1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.4/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


On the Serveur 2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 12 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.6
                      ip address 10.0.5/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core_1
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint


  On the vsx Core_2
!
vlan 4 (Transit_vlan beetween srv and core)
                     vsx-sync
!
interface lag 11 multi-chassis  
                      no shut
                      no routing
                      vlan trunk allowed 4
                      lacp mode active
!
interface vlan 4
                      vsx active-gateway
                      vsx active-gateway ip mac 12:01:00:00:01:00
                      vsx active-gateway ip 10.0.0.3
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 08, 2021 06:31 AM
From: Kamal Takodra
Subject: ARUBA 8325 VSX and OSPF

You cannot have a Layer3 LAG and Layer 2 LAG  on same interface.

Your options are

1. Have a Layer 3 LAG with an IP address on it and its a routed port and then define your routing requirements here i.e OSPF in your case

or

2 . Have a Layer 2 LAG with an allowed VLAN on it.
You would then need a VLAN defined which you then put your routing parameters on i.e OSPF in your case

for example
!
interface lag 100 multi-chassis
no shutdown
no routing
vlan access 100  <-----you can use a VLAN TRUNK ALLOWED and specify the vlan
lacp mode active
!
interface vlan 100
vsx active-forwarding
ip address 10.100.100.1/30
ip ospf 1 area 0.0.0.0
no ip ospf passive
!
router ospf 1
router-id 10.254.254.1
passive-interface default
area 0.0.0.0








------------------------------
Kamal Takodra
If my post was useful accept solution and/or give kudos

Original Message:
Sent: Feb 08, 2021 03:43 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF


Thank for your return, but i need to be sure for my configuration.

I need to configure a IP for my point to point on the interface lag, like this?

On the vsx Serveur
interface lag 12 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed 200 (this is the vlan of my Server)
                      lacp mode active
                      ip address 10.0.2/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint



  On the vsx Core
interface lag 11 multi-chassis
                      vsx-sync
                      no shut
                      no routing
                      vlan trunk allowed all
                      lacp mode active
                      ip address 10.0.1/31
                      ip ospf 1 area 0.0.0.0
                      no ip ospf passive
                      ip ospf cost 1000
                      ip ospf network Point-toPoint
Original Message:
Sent: Feb 06, 2021 10:21 AM
From: Alexis La Goutte
Subject: ARUBA 8325 VSX and OSPF

Hi Artnod

you can configure a ip address on lag interface with Aruba CX

------------------------------
PowerArubaSW : Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP...

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...)

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)..

ACEP / ACMX #107 / ACDX #1281

Original Message:
Sent: Feb 04, 2021 10:50 AM
From: Unknown User
Subject: ARUBA 8325 VSX and OSPF

Hi evryone!!!

I have a question :

I would like to set up OSPF Point to Point between my two VSX, I know how to set up the OSPF Point 2 point between a vsx and a Switch alone, but whit 2 vsx, where i configure the OSPF ?

For my old configuration I confugure a @IP OSPF (in blue) on every interface, but with the vsx LAG where can i configure the OSPF IP?

​