Wired Intelligent Edge

Hello all,

I have a problem with some of my ProCurve ports being blocked by STP. Is there an explanation for this?


I 09/23/10 12:27:57 00077 ports: port 44 is now off-line
I 09/23/10 12:28:20 00435 ports: port 44 is Blocked by STP
I 09/23/10 12:28:23 00076 ports: port 44 is now on-line
I 09/23/10 12:28:32 00077 ports: port 44 is now off-line
I 09/23/10 12:28:39 00435 ports: port 44 is Blocked by STP
I 09/23/10 12:28:42 00076 ports: port 44 is now on-line
I 09/23/10 12:31:50 00435 ports: port 14 is Blocked by STP
I 09/23/10 12:31:53 00076 ports: port 14 is now on-line
I 09/23/10 12:32:16 00077 ports: port 14 is now off-line
I 09/23/10 12:32:29 00435 ports: port 14 is Blocked by STP
I 09/23/10 12:32:32 00076 ports: port 14 is now on-line
I 09/23/10 12:33:01 00077 ports: port 44 is now off-line
I 09/23/10 12:33:07 00435 ports: port 44 is Blocked by STP
I 09/23/10 12:33:09 00076 ports: port 44 is now on-line
I 09/23/10 12:33:47 00077 ports: port 44 is now off-line
I 09/23/10 12:33:58 00435 ports: port 44 is Blocked by STP
I 09/23/10 12:34:01 00076 ports: port 44 is now on-line
I 09/23/10 12:35:37 00077 ports: port 44 is now off-line
I 09/23/10 12:36:26 00435 ports: port 32 is Blocked by STP
I 09/23/10 12:36:29 00076 ports: port 32 is now on-line
I 09/23/10 12:37:32 00077 ports: port 32 is now off-line
I 09/23/10 12:38:01 00435 ports: port 29 is Blocked by STP
I 09/23/10 12:38:03 00076 ports: port 29 is now on-line
I 09/23/10 12:38:52 00077 ports: port 29 is now off-line
I 09/23/10 12:39:11 00435 ports: port 44 is Blocked by STP
I 09/23/10 12:39:14 00076 ports: port 44 is now on-line
I 09/23/10 12:40:36 00077 ports: port 44 is now off-line
I 09/23/10 12:41:12 00435 ports: port 2 is Blocked by STP
I 09/23/10 12:41:15 00076 ports: port 2 is now on-line
I 09/23/10 12:42:28 00077 ports: port 2 is now off-line
I 09/23/10 12:42:44 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:42:45 00077 ports: port 31 is now off-line
I 09/23/10 12:42:47 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:42:47 00077 ports: port 31 is now off-line
I 09/23/10 12:42:49 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:42:49 00077 ports: port 31 is now off-line
I 09/23/10 12:42:51 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:42:52 00077 ports: port 31 is now off-line
I 09/23/10 12:42:54 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:42:54 00077 ports: port 31 is now off-line
I 09/23/10 12:42:56 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:42:59 00076 ports: port 31 is now on-line
I 09/23/10 12:43:11 00077 ports: port 31 is now off-line
I 09/23/10 12:43:51 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:43:52 00077 ports: port 31 is now off-line
I 09/23/10 12:43:54 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:43:55 00077 ports: port 31 is now off-line
I 09/23/10 12:43:56 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:43:57 00077 ports: port 31 is now off-line
I 09/23/10 12:43:59 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:44:00 00077 ports: port 31 is now off-line
I 09/23/10 12:44:02 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:44:02 00077 ports: port 31 is now off-line
I 09/23/10 12:44:04 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:44:05 00077 ports: port 31 is now off-line
I 09/23/10 12:44:07 00435 ports: port 31 is Blocked by STP
I 09/23/10 12:44:09 00076 ports: port 31 is now on-line
I 09/23/10 12:46:31 00077 ports: port 45 is now off-line
I 09/23/10 12:46:38 00435 ports: port 45 is Blocked by STP
I 09/23/10 12:46:40 00076 ports: port 45 is now on-line

 

P.S. This thread has been moved from  Switches, Hubs, Modems (Legacy ITRC forum) to ProCurve / ProVision-Based. -HP Forum Moderator

#BlockedbySTPprocurvehp5406zl
#blocking
#ProCurve
#STP
#port_mirror

Hi,

What devices are connected on those ports?

STP is the Spanning Tree Protocol which prevents loops on your network.
If you were not using STP and something created a loop on your network (either your resilient design or someone connecting the same cable to a swtich twice) then it would probably cause your network to stop working.

You need to find what devices are connected on those switch ports and determine whether the loop is valid.

in addition to Mohammeds post

All ports can potentially create a loop.
(think of two wall-outlets patched to one another!).

So When spanning-tree is enabled, potentially all ports need to participate in the spanning-tree protocol.
Even client ports!
Every client on/of/rebooot/connect/disconnect can produce such a message.

you need to specifically configure the port not to participate in spnning-tree operation.

You can disable logging these on/of events on these ports.

Strange that three days ago the ports of some end points were blocked and noes were causing the network loop.
Example the point that a printer was connected blocked alone, after shutdown end no shutdown the port returned UP.

Sorry, I was reading your log the wrong way around! (I'm used to doing a "show log -r" :) )
That is normal behaviour, whenever a port goes offline and comes back online you will see in your logs

- port X is now off-line
- port X is Blocked by STP
- port X is now on-line

That will happen even if you aren't running STP.

Ok! But see de log attached, port 2, 5 and 44, pleased!

- the switch has stp active
- a port comes up (=> the PC is switched on
)
- the switch does not know what's connected and if a loop has formed
- so it initially puts the port in the STP blocked state
I 09/20/10 11:30:53 00435 ports: port 2 is Blocked by STP
- goes through listening and learning states
- concludes there is no loop
- unblocks the port (port is now on-line)
I 09/20/10 11:30:55 00076 ports: port 2 is now on-line
- the PC is shut down for the night
I 09/20/10 17:43:48 00077 ports: port 2 is now off-line

This is normal behaviour

I think the sequence that is being referred to is this:

I 09/23/10 12:41:12 00435 ports: port 2 is Blocked by STP

I 09/23/10 12:41:15 00076 ports: port 2 is now on-line

I 09/23/10 12:42:28 00077 ports: port 2 is now off-line

The first two entries are normal as Pieter describes above.
The third entry occurs 45 seconds later which suggests to me that it's a client issue. There is also nothing in the logs to suggest that MSTP is disabling the port.
If you want to test that try disabling STP on that port and seeing if you still have an issue:

# spanning-tree 2 admin-edge-port

Hi,

i have the same error but "spanning-tree 12 admin-edge-port" does not solve. The port 12 on my setup is connected to VMWare device.

Try filter(s) with loop-protect.  Might help in your situation

span <port_list> admin-edge-port Makes port(s) an admin edge port. Used for connected to end devices.
span <port_list> pvst-protect Shuts <port_list> down the port if it receives a pvst bpdu.  Stays down for the  bpdu-protection-timeout period
span <port_list> bpdu-protection  Shuts <port_list> down the port if it receives a m/r/stp bpdu.  Stays down for the  bpdu-protection-timeout period
span bpdu-protection-timeout 600 Times out <port_list> with protection enable on them for 10 minutes
span <port_list> pvst-filter Stops the port from transmitting or receiving pvst bpdu’s. The port will continuously forward traffic. Useful for bridging devices
span <port_list> bpdu-filter Stops the port from transmitting or receiving m/r/stp bpdu’s. The port will continuously forward traffic. Useful for bridging devices
loop-protect <port_list> Will prevent loops from down stream switches as well
span trap errant-bpdu loop-guard new-root Sends a trap to server for every event listed

Hi guys,

 

i have a question about this "Blocked by STP" - is this event log imposieble sent to e-mail inside my company?

 

Thanks!

I have an issue with My AP's being blocked by STP. I work for a University and we have found in past instances that students will bridge thier NIC's (Wired and Wireless) thinking they will get faster connections. This is the reason we turned spanning tree on. Is there a way to make sure that the port with the AP always takes priority or that it never gets blocked?

also had this prob i tried to disconnect the trk and the reduenduent link no help

Please create a new thread for any new posts with as much detail relating to your switch modes/configs and we can see if we can help you out. Thanks.