Wired Intelligent Edge

Hello Everybody

I have some trouble with my new module J9988A (v3) HP 24p 1GbE SFP v3 zl2 Mod

It isn't recognized on my switch 5412R zl2 J9851a I think It is a V2 switch but Aruba tells me tat there is a compatibility between V2 chassis and V3 module

I have installed KB.16.02.0028, ROM KB.16.01.0006  I think it's the latest firmware but no luck

Hi Houss78300,

What you reported is pretty strange...the SKU J9988A is a v3 zl2 Module compatible with HP/Aruba 5400R zl2 switch series chassis either working in v2 Compatibility Mode or in v3-Only Mode (where here v2 and v3 refer to the version of zl and zl2 Modules families respectively)....more than that the KB.16.02.0028 software version your HP 5400R zl2 is running on is really recent and it supports all v2 zl and v3 zl2 Modules compatbile with HP/Aruba 5400R zl2 Switch series (figure out that the J9988A is supported since KB.15.17)...so it's really strange.

Can you post the sanitized logs - show logs (trim to post only Module insertion relevant) - which refer to Module insertion time? can you also post the output of show flash, show version and show modules commands?

A sanitized running configuration would be of help eventually.

Hello and thank you very much for your tim

this is my log

show log

I 0038:04:54:27.35 00068 chassis: AM1: Slot A Inserted
I 0038:04:54:43.87 03846 InSysProg: AM1: Slot A: Checking for firmware updates.
W 0038:04:54:43.87 00072 chassis: AM1: Slot A Inactive: Module/Configuration mismatch

show flash

Image Size (bytes) Date Version
----------------- ------------ -------- --------------
Primary Image : 30322750 10/28/19 KB.16.02.0028
Secondary Image : 30322750 10/28/19 KB.16.02.0028

Boot ROM Version
----------------
Primary Boot ROM Version : KB.16.01.0006
Secondary Boot ROM Version : KB.16.01.0006

Default Boot Image : Primary
Default Boot ROM : Primary

and show module

Status and Counters - Module Information

Chassis: 5412Rzl2 J9851A Serial Number: SG71G4B0KM

Allow V2 Modules: Yes

Core Mod
Slot Module Description Serial Number Status Dump Ver
----- -------------------------------------- -------------- -------- ----- ---
MM1 HP J9827A Management Module 5400Rzl2 SG71G4C1TQ Active YES 1
MM2 HP J9827A Management Module 5400Rzl2 SG70G4C0T1 Standby YES 1

A Failed -
B HP J9549A 20p GT / 4P SFP v2 zl Mod SG7168B02N Up YES 2
C HP J9550A 24p Gig-T v2 zl Module SG7297Z07V Up YES 2
D HP J9549A 20p GT / 4P SFP v2 zl Mod SG7168B00Y Up YES 2
E HP J9550A 24p Gig-T v2 zl Module SG7277Z053 Up YES 2
F HP J9550A 24p Gig-T v2 zl Module SG7277Z06P Up YES 2
G HP J9550A 24p Gig-T v2 zl Module SG7277Z00R Up YES 2
H HP J9550A 24p Gig-T v2 zl Module SG7277Z01G Up YES 2
I HP J9550A 24p Gig-T v2 zl Module SG7277Z01K Up YES 2
J HP J9550A 24p Gig-T v2 zl Module SG7277Z02R Up YES 2
K HP J9550A 24p Gig-T v2 zl Module SG7277Z01X Up YES 2
L HP J9550A 24p Gig-T v2 zl Module SG7277Z055 Up YES 2

I think it's the same case like this post

https://community.hpe.com/t5/Aruba-ProVision-based/Installing-new-modules-in-5412Rzl2-chassis/m-p/6927672#M11271

But I can't erase my switch config it's already in production

Hello,
The message in the log means that slot A is currently configured for another type of module

W 0038:04:54:43.87 00072 chassis: AM1: Slot A Inactive: Module/Configuration mismatch

So probably you had a module of another type in slot A before, different than J9988A.
It is not necessary to reset the configuration. There is a procedure to change the slot configuration/type during normal operation.
Have a look at this document and try to procedure in the section "Resolution"

https://support.hpe.com/hpsc/doc/public/display?docLocale=en_US&docId=emr_na-c05205857&withFrame

thank you very much !!!!!