Comware

Hello team,

I have a problem with POE in this switch. I have plug in two camera and one Access Point. one camera in the port 3 work properly and the access point in the port 10 work properly but the camera in the port 9 doesn't work. The switch always show me this message (%Jan 21 20:45:12:633 2013 10.171.9.104 POE/1/PSE_PORT_ON_OFF_CHANGE:
Trap <pethPsePortOnOffNotification>: PSE 4, IfIndex 9, Detection Status 1.) and (%Jan 21 20:45:15:741 2013 10.171.9.104 POE/1/PSE_PORT_ON_OFF_CHANGE:
Trap <pethPsePortOnOffNotification>: PSE 4, IfIndex 9, Detection Status 3.)

dis boot-loader :

Software images on slot 1:
Current software images:
flash:/5130ei-cmw710-boot-r3113p05.bin
flash:/5130ei-cmw710-system-r3113p05.bin
Main startup software images:
flash:/5130ei-cmw710-boot-r3113p05.bin
flash:/5130ei-cmw710-system-r3113p05.bin

-->dis poe device 

PSE ID Slot No. SSlot No. PortNum MaxPower(W) State Model
4 1 0 24 370.0 On LSP7POED

-->dis poe interface 

Interface PoE Priority CurPower Oper IEEE Detection
(W) Class Status
GE1/0/1 Enabled Low 0.0 Off 0 Searching
GE1/0/2 Enabled Low 0.0 Off 0 Searching
GE1/0/3 Enabled Low 3.5 On 2 Delivering Power
GE1/0/4 Enabled Low 0.0 Off 0 Searching
GE1/0/5 Enabled Low 0.0 Off 0 Searching
GE1/0/6 Enabled Low 0.0 Off 0 Searching
GE1/0/7 Enabled Low 0.0 Off 0 Searching
GE1/0/8 Enabled Low 0.0 Off 0 Searching
GE1/0/9 Enabled Low 2.1 On 1 Delivering Power
GE1/0/10 Enabled Low 4.9 On 4 Delivering Power
GE1/0/11 Enabled Low 0.0 Off 0 Searching
GE1/0/12 Enabled Low 0.0 Off 0 Searching
GE1/0/13 Enabled Low 0.0 Off 0 Searching
GE1/0/14 Enabled Low 0.0 Off 0 Searching
GE1/0/15 Enabled Low 0.0 Off 0 Searching
GE1/0/16 Enabled Low 0.0 Off 0 Searching
GE1/0/17 Enabled Low 0.0 Off 0 Searching
GE1/0/18 Enabled Low 0.0 Off 0 Searching
GE1/0/19 Enabled Low 0.0 Off 0 Searching
GE1/0/20 Enabled Low 0.0 Off 0 Searching
GE1/0/21 Enabled Low 0.0 Off 0 Searching
GE1/0/22 Enabled Low 0.0 Off 0 Searching
GE1/0/23 Enabled Low 0.0 Off 0 Searching
GE1/0/24 Enabled Low 0.0 Off 0 Searching
--- On State Ports: 3; Used: 10.5(W); Remaining: 359.5(W) ---

--> this camera when I put it the procurve sawitch it work but in the HP comware 5130 doesn't work. The camera which are working has 1 CAM heads and the second one that it doesn'T work have 2 CAM to see both direction.

But when I add an POE adapter it work.

Please can you help me.

Thank very much and have a good day

Yassine Thabet
Delivery Network
DRÄXLMAIER Group

P.S: Admin: Moved as a new Topic from PoE issue with 5130 JG937A 

Hi,

What is the configuration of your interfaces (Gi1/0/3, 9 and 10)?

NB: You might want to look at your clock on your switch. (The log-entries your posted "(%Jan 21 20:45:12:633 2013 10.171.9.104 POE/1/PSE...)" are either very old or your clock is wrong.

Regards

Hi,

The config of the interface 3, 9 and 10 is the same :

port access vlan 163
mdix-mode mdix
stp edged-port
poe enable

For the clock is wrong I have correct it.

Thank you very much

Hi,

Why have you forced the MDIX-mode to MDIX?

Unless you have problems with the autoMDIX mode and know what cables and what mode the peer uses, I would strongly suggest you to go with the default, which is auto.

mdix-mode automdix  (or equivalent undo mdix-mode mdix)

Regards