Wired Intelligent Edge

 View Only

  • 1.  use of 10G SFP modules on the HP-2530-48G-2SFPP , HP 2530-24 and HP-2530-8G-PoEP switches

    Posted Sep 16, 2025 03:49 PM

    Hi 
    I was wondering if it's possible to use 10G SFP modules on those switches
    I have upgraded them to the last firmware YA_16_11_0026 but it does not seem to recognize them
    i have the option the  "allow-unsupported-transceiver" command to enable 3rd party transeivers



    -------------------------------------------


  • 2.  RE: use of 10G SFP modules on the HP-2530-48G-2SFPP , HP 2530-24 and HP-2530-8G-PoEP switches

    Posted Sep 16, 2025 05:14 PM

    The HP-2530-48G-2SFPP has 2 ports SFP+ which gives you 1/10Gbps

    I am not sure if HP 2530-24 and HP-2530-8G-PoE has 10G, as far as i have seen on the Datasheet, the Aruba 2530-24 Switch (J9782A) and Aruba 2530-8G-PoE+ Switch (J9774A)  has only 1G Ports 



    ------------------------------
    Shpat | ACEP | ACMP | ACCP | ACDP
    Just an Aruba enthusiast and contributor by cases
    If you find my comment helpful, KUDOS are appreciated.
    ------------------------------



  • 3.  RE: use of 10G SFP modules on the HP-2530-48G-2SFPP , HP 2530-24 and HP-2530-8G-PoEP switches

    Posted Sep 16, 2025 07:07 PM

    thats correct he Aruba 2530-24 Switch (J9782A) and Aruba 2530-8G-PoE+ Switch (J9774A)  has only 1G Ports 



    ------------------------------
    If my post was useful accept solution and/or give kudos.
    Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
    ------------------------------

    Original Message


  • 4.  RE: use of 10G SFP modules on the HP-2530-48G-2SFPP , HP 2530-24 and HP-2530-8G-PoEP switches

    Posted Sep 17, 2025 01:05 AM

    Thank you for the info , 

    the problem is that the HP-2530-48G-2SFPP does not recognize my 10g module connection remains down 

    i have tried 2 new module from FS multimode

    is there something else I could try ? 



    ------------------------------
    peter
    ------------------------------

    Original Message


  • 5.  RE: use of 10G SFP modules on the HP-2530-48G-2SFPP , HP 2530-24 and HP-2530-8G-PoEP switches

    Posted Sep 17, 2025 01:25 AM

    There is a compatibility matrix of SFP which work for specific switches:
    https://arubanetworking.hpe.com/techdocs/Switches/xcvrs/xcvr_guide/Content/Chp_sfp/gig-sfp-mod-spe-com.htm

    Aruba/HPE does not guarantee non-Aruba or non-HPE branded optics or DACs will work reliably.

    You can run the command: allow-unsupported-transceiver 
    And then check the status of the interface, but even 3rd party transceivers most of the time have to be specific for the Partnumber/Model of the switch. 
    If you order 3rd party transceiver for HP-2530-48G-2SFPP and it doesn't work, you should check with your SFP supplier, because they might have the wrong code in it and the switch is not supported / or lets say switch will not support the SFP.



    ------------------------------
    Shpat | ACEP | ACMP | ACCP | ACDP
    Just an Aruba enthusiast and contributor by cases
    If you find my comment helpful, KUDOS are appreciated.
    ------------------------------

    Original Message


  • 6.  RE: use of 10G SFP modules on the HP-2530-48G-2SFPP , HP 2530-24 and HP-2530-8G-PoEP switches

    Posted Sep 17, 2025 01:31 AM

    Is there anything there in logs entries at that time when you plug in transceiver to switch?

    How about "show tech transceivers" after you have plugged module in?



    ------------------------------
    Jori Luoto
    AV-IT Specialist
    Audico Systems oy
    ------------------------------

    Original Message


  • 7.  RE: use of 10G SFP modules on the HP-2530-48G-2SFPP , HP 2530-24 and HP-2530-8G-PoEP switches

    Posted Sep 17, 2025 08:21 AM

    Hello Peter,

    HP-2530-48G-2SFP+ (2 SFP+ uplink ports)
    Only the 2 uplink ports labeled SFP+ on this model are for 10 GbE; the other SFP slots are for 1 GbE. (The HP/Aruba 2530-48G-2SFP+ data sheet explicitly states this.)
    https://www.router-switch.com/pdf2html/pdf/j9855a-datasheet.pdf

    Be sure to insert the module into the 10G uplink ports labeled "SFP+". If the label on the chassis says SFP, that port is 1G; it does not support 10G.

    The 10GBASE-SR module will not link to a device with 1G SFP on the other end. The remote end must also have 10G SFP+ SR/LR. (The 10G SFP+ module will not downgrade to 1G.)

    SR modules require OM3/OM4 MMF and LC-LC. SR does not work with SMF (OS2) patch. If you are going through a patch panel, verify the polarity (A-B); if the cross is wrong, the link will not come at all. (J9150A/J9150D SR types are subject to these requirements.)
    https://www.router-switch.com/pdf2html/pdf/j9150d-datasheet.pdf

    Can you run and share these commands?
    show version
    show interfaces transceiver detail
    show logging -r | include transceiver

    -------------------------------------------

    Original Message


Related Content