Network Management

We have port-security enabled on our ports so only registered mac-addresses get connection.  We're thinking about getting VoIP phones, and since these phones will have a mac-address, they also need to be entered on the mac-address table correct?  Also increase the limit of mac-address.

Just want to make sure

Anyone confirm?
Original Message:
Sent: Oct 18, 2022 03:54 PM
From: Tony Antony
Subject: Voip phones, port security

We have port-security enabled on our ports so only registered mac-addresses get connection.  We're thinking about getting VoIP phones, and since these phones will have a mac-address, they also need to be entered on the mac-address table correct?  Also increase the limit of mac-address.

Just want to make sure

If this is a CX switch, you will have to add the phone MAC address to the list and increase the limit on the port.

You can set the port to sticky with a limit of 2.
Original Message:
Sent: Oct 19, 2022 02:00 PM
From: Tony Antony
Subject: Voip phones, port security

Anyone confirm?
Original Message:
Sent: Oct 18, 2022 03:54 PM
From: Tony Antony
Subject: Voip phones, port security

We have port-security enabled on our ports so only registered mac-addresses get connection.  We're thinking about getting VoIP phones, and since these phones will have a mac-address, they also need to be entered on the mac-address table correct?  Also increase the limit of mac-address.

Just want to make sure

ok, its a 2390f
Original Message:
Sent: Oct 20, 2022 07:39 PM
From: Shieva Eccles
Subject: Voip phones, port security

If this is a CX switch, you will have to add the phone MAC address to the list and increase the limit on the port.

You can set the port to sticky with a limit of 2.
Original Message:
Sent: Oct 19, 2022 02:00 PM
From: Tony Antony
Subject: Voip phones, port security

Anyone confirm?
Original Message:
Sent: Oct 18, 2022 03:54 PM
From: Tony Antony
Subject: Voip phones, port security

We have port-security enabled on our ports so only registered mac-addresses get connection.  We're thinking about getting VoIP phones, and since these phones will have a mac-address, they also need to be entered on the mac-address table correct?  Also increase the limit of mac-address.

Just want to make sure

Its almost the same.

You can use a static learn mode with an address-limit of 2 to only allow the first 2 devices on the port to be allowed.

Aruba-2930F-8G-PoEP-2SFPP(config)# show port-security 2

Port Security

Port : 2
Learn Mode [Continuous] : Static Address Limit [1] : 2
Action [None] : None
Eavesdrop Prevention [Enabled] : Enabled
Disable Timer : 0

Authorized Addresses
--------------------
Original Message:
Sent: Oct 21, 2022 08:49 AM
From: Tony Antony
Subject: Voip phones, port security

ok, its a 2390f
Original Message:
Sent: Oct 20, 2022 07:39 PM
From: Shieva Eccles
Subject: Voip phones, port security

If this is a CX switch, you will have to add the phone MAC address to the list and increase the limit on the port.

You can set the port to sticky with a limit of 2.
Original Message:
Sent: Oct 19, 2022 02:00 PM
From: Tony Antony
Subject: Voip phones, port security

Anyone confirm?
Original Message:
Sent: Oct 18, 2022 03:54 PM
From: Tony Antony
Subject: Voip phones, port security

We have port-security enabled on our ports so only registered mac-addresses get connection.  We're thinking about getting VoIP phones, and since these phones will have a mac-address, they also need to be entered on the mac-address table correct?  Also increase the limit of mac-address.

Just want to make sure