Hi,
I work with Giuseppe, I will help him on networking.
We stopped the VRRP test for 2 weeks.
The vrrp interface on vlan 102 effectively was in shutdown. Now we enabled it as you can see from the cfg:
interface vlan 102
ip address 192.168.102.240/24
vrrp 102 address-family ipv4
address 192.168.102.253 secondary
priority 230
no shutdown
exit
The "(Group Disabled)" on 6400 is no more disabled
Interface vlan102 - Group 102 - Address-Family IPv4
State is INIT (No Primary Group Address)
State duration
Virtual IP address is no address
Virtual secondary IP addresses:
192.168.102.253
Virtual MAC address is 00:00:5e:00:01:66
Advertisement interval is 1000 msec
Version is 2
Preemption is enabled
min delay is 0 sec
Priority is 230
Active Router is 192.168.102.250
Active Advertisement interval is 1000 msec
Active Down interval is 3101 msec
The VLAN Group102 is in INIT State and I think it means that is not "working"
On this switch priority is 230; instead on the 5406 (IP 192.168.102.250) priority is set to 220.
Roberto
Original Message:
Sent: Sep 20, 2023 08:28 AM
From: davidwk
Subject: VRRP between 6400 and 5406
You also need to do a no shutdown on the vrrp interface on vlan 102. Your config for that vlan interface should look like this (note the added no shutdown)
interface vlan 102 ip address 192.168.102.240/24 vrrp 102 address-family ipv4 address 192.168.102.253 primary priority 230 no shutdown exit
Original Message:
Sent: Sep 20, 2023 08:19 AM
From: giuseppe.montanarella@manet.it
Subject: VRRP between 6400 and 5406
Wi did it but nothing change :-(
Giuseppe
Original Message:
Sent: Sep 20, 2023 02:53 AM
From: ariyap
Subject: VRRP between 6400 and 5406
the "(Group Disabled)"on the 6400, indicates that interface vlan 102 is shutdown.
can you do a no shut on it and see if it works?
------------------------------
If my post was useful accept solution and/or give kudos.
Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
Original Message:
Sent: Sep 20, 2023 02:19 AM
From: giuseppe.montanarella@manet.it
Subject: VRRP between 6400 and 5406
6400
CED00# sh vrrp
VRRP is enabled
Interface vlan102 - Group 102 - Address-Family IPv4
State is INIT (Group Disabled)
State duration
Virtual IP address is 192.168.102.253
Virtual MAC address is 00:00:5e:00:01:66
Advertisement interval is 1000 msec
Version is 2
Preemption is enabled
min delay is 0 sec
Priority is 230
Active Router is 0.0.0.0
Active Advertisement interval is 1000 msec
Active Down interval is 3101 msec
CED00#
5406
CED01# sh vrrp
VRRP Global Statistics Information
VRRP Enabled : Yes
Protocol Version : 2
Invalid VRID Pkts Rx : 0
Checksum Error Pkts Rx : 0
Bad Version Pkts Rx : 0
Virtual Routers Respond To Ping Requests : Yes
VRRP Virtual Router Statistics Information
Vlan ID : 102
Virtual Router ID : 102
State : Backup
Up Time : 27 days
Virtual MAC Address : 00005e-000166
Master's IP Address : 192.168.102.250
Associated IP Addr Count : 1 Near Failovers : 3197
Advertise Pkts Rx : 2345598 Become Master : 1
Zero Priority Rx : 0 Zero Priority Tx : 0
Bad Length Pkts : 0 Bad Type Pkts : 0
Mismatched Interval Pkts : 0 Mismatched Addr List Pkts : 0
Mismatched IP TTL Pkts : 0 Mismatched Auth Type Pkts : 0
Original Message:
Sent: Sep 19, 2023 08:54 AM
From: davidwk
Subject: VRRP between 6400 and 5406
Can you post the output of show vrrp from both switches?
Original Message:
Sent: Sep 19, 2023 08:42 AM
From: giuseppe.montanarella@manet.it
Subject: VRRP between 6400 and 5406
Hi, in attach the 2 files with the configuration.
Original Message:
Sent: Sep 15, 2023 09:46 PM
From: ariyap
Subject: VRRP between 6400 and 5406
There should not be issues as VRRP is fully standards-based and supported by both OSs.
what is the exact issue/error you are getting?
------------------------------
If my post was useful accept solution and/or give kudos.
Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.