Controllerless Networks

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.

Thanks for your reply, I posted in the wrong place. There are 2 standby controllers, and I configured them with L2 redundancy. After completing the entire configuration without any issues, I shut down the master device to test the failover scenario. However, I couldn't see the WLANs on the backup device. Apart from this, all configurations were present and complete.

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.

Which software version are you using? AOS8? Sounds like you are using the old master/standby master setup. Is that correct?

Thanks for your reply, I posted in the wrong place. There are 2 standby controllers, and I configured them with L2 redundancy. After completing the entire configuration without any issues, I shut down the master device to test the failover scenario. However, I couldn't see the WLANs on the backup device. Apart from this, all configurations were present and complete.

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.

The version is AOS8 which is 8.10. The model of devices 9012 

Which software version are you using? AOS8? Sounds like you are using the old master/standby master setup. Is that correct?

Thanks for your reply, I posted in the wrong place. There are 2 standby controllers, and I configured them with L2 redundancy. After completing the entire configuration without any issues, I shut down the master device to test the failover scenario. However, I couldn't see the WLANs on the backup device. Apart from this, all configurations were present and complete.

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.

Are you using the Mobility Conductor? If not, the master controller deployment model is not support since version 8.7. I believe you can still configure it but officially it's not supported.

The version is AOS8 which is 8.10. The model of devices 9012 

Which software version are you using? AOS8? Sounds like you are using the old master/standby master setup. Is that correct?

Thanks for your reply, I posted in the wrong place. There are 2 standby controllers, and I configured them with L2 redundancy. After completing the entire configuration without any issues, I shut down the master device to test the failover scenario. However, I couldn't see the WLANs on the backup device. Apart from this, all configurations were present and complete.

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.

Thanks for your explanation. So, in version 8.10, I cannot configure VRRP without using a Mobility Conductor, did I understand that correctly?

Are you using the Mobility Conductor? If not, the master controller deployment model is not support since version 8.7. I believe you can still configure it but officially it's not supported.

The version is AOS8 which is 8.10. The model of devices 9012 

Which software version are you using? AOS8? Sounds like you are using the old master/standby master setup. Is that correct?

Thanks for your reply, I posted in the wrong place. There are 2 standby controllers, and I configured them with L2 redundancy. After completing the entire configuration without any issues, I shut down the master device to test the failover scenario. However, I couldn't see the WLANs on the backup device. Apart from this, all configurations were present and complete.

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.

You can still configure it but it is not supported anymore. 

If you really want this kind of setup please you the master-local setup. That was a common deployment model during the AOS6 time. However, I recommended you to look into the setup with a Mobility Conductor.

Thanks for your explanation. So, in version 8.10, I cannot configure VRRP without using a Mobility Conductor, did I understand that correctly?

Are you using the Mobility Conductor? If not, the master controller deployment model is not support since version 8.7. I believe you can still configure it but officially it's not supported.

The version is AOS8 which is 8.10. The model of devices 9012 

Which software version are you using? AOS8? Sounds like you are using the old master/standby master setup. Is that correct?

Thanks for your reply, I posted in the wrong place. There are 2 standby controllers, and I configured them with L2 redundancy. After completing the entire configuration without any issues, I shut down the master device to test the failover scenario. However, I couldn't see the WLANs on the backup device. Apart from this, all configurations were present and complete.

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.

It's not recommended, but it seems like it would still work without issues - that's how I understand it. So why aren't the SSIDs appearing?

You can still configure it but it is not supported anymore. 

If you really want this kind of setup please you the master-local setup. That was a common deployment model during the AOS6 time. However, I recommended you to look into the setup with a Mobility Conductor.

Thanks for your explanation. So, in version 8.10, I cannot configure VRRP without using a Mobility Conductor, did I understand that correctly?

Are you using the Mobility Conductor? If not, the master controller deployment model is not support since version 8.7. I believe you can still configure it but officially it's not supported.

The version is AOS8 which is 8.10. The model of devices 9012 

Which software version are you using? AOS8? Sounds like you are using the old master/standby master setup. Is that correct?

Thanks for your reply, I posted in the wrong place. There are 2 standby controllers, and I configured them with L2 redundancy. After completing the entire configuration without any issues, I shut down the master device to test the failover scenario. However, I couldn't see the WLANs on the backup device. Apart from this, all configurations were present and complete.

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.

It's not recommended, but it seems like it would still work without issues - that's how I understand it. So why aren't the SSIDs appearing?

You can still configure it but it is not supported anymore. 

If you really want this kind of setup please you the master-local setup. That was a common deployment model during the AOS6 time. However, I recommended you to look into the setup with a Mobility Conductor.

Thanks for your explanation. So, in version 8.10, I cannot configure VRRP without using a Mobility Conductor, did I understand that correctly?

Are you using the Mobility Conductor? If not, the master controller deployment model is not support since version 8.7. I believe you can still configure it but officially it's not supported.

The version is AOS8 which is 8.10. The model of devices 9012 

Which software version are you using? AOS8? Sounds like you are using the old master/standby master setup. Is that correct?

Thanks for your reply, I posted in the wrong place. There are 2 standby controllers, and I configured them with L2 redundancy. After completing the entire configuration without any issues, I shut down the master device to test the failover scenario. However, I couldn't see the WLANs on the backup device. Apart from this, all configurations were present and complete.

you need to provide more info. you have posted in controller-less discussion group but I am assuming you are are talking about controllers.